Coat It Blue Product Instructions

Español

Coat It Part # (found on the bottom of front panel on product)

DIRECTIONS: While wearing proper personal protecive equipment simply spray product on rag then wipe off overspray area. Product can also be poured into Coat It spray equpment to clean equpment out.

PRECAUTIONARY STATEMENT(S):

  • Keep away from heat sparks/ open flames/hot surfaces.
  • No smoking.
  • Keep container tightly closed. Ground/bond container and receiving equipment.
  • Use explosion-proof electrical/ventilating/lighting equipment.
  • Use only non-sparking tools.
  • Take precautionary measures against static discharge.
  • Avoid breathing dust/fume/gas/mist/vapors/spray.
  • Wash hands and other exposed areas thoroughly after handling.
  • Do not eat, drink or smoke when using this product.
  • Use only outdoors or
    in a well-ventilated area.
  • Wear protective gloves/eye protection/
    face protection.
  1. IF SWALLOWED: Call a POISON CENTER/doctor
    if you feel unwell.
  2. IF ON SKIN: Wash with plenty of water and mild soap. Take off immediately all contaminated clothing. Rinse skin with water/shower.
  3. IF INHALED: Remove person to fresh air and keep comfortable for breathing.
  4. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
  5. Call a POISON CENTER/doctor if you feel unwell.

If skin irritation occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.Take off contaminated clothing and wash it before reuse. In case of fire: Use carbon dioxide to extinguish. Store in a well-ventilated place. Keep cool. Dispose of contents/container to the specifications of local, regional, national, and international regulations.

ADDITIONAL PRECAUTIONS FOR SAFE HANDLING: Do not handle until all safety precautions have been read and understood. Avoid contact with skin, eyes and clothing. Do not breathe gas, mist, spray, vapors. Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and when leaving work. Do not spray on open flame or other ignition source.

CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES: Technical Measures: Comply with applicable regulations. Proper grounding procedures to avoid static electricity should be followed. Storage Conditions: Store in a dry, cool place. Keep only in the original container in a cool, well-ventilated place away from ignition sources. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122° F. Keep/ Store away from direct sunlight, extremely high or low temperatures and incompatible materials. Store locked up/in a secure area. Incompatible Materials: Strong acids, strong bases, strong oxidizers. Chlorine. Finely divided metals. Magnesium. Alkaline earth metals.

FIRST AID MEASURES: General Advice:Never give anything by mouth to an unconscious person. If you
feel unwell, seek medical advice (show the label where possible).IF INHALED: First, take proper precautions to ensure your own safety before attempting rescue (e.g. wear appropriate respiratory protective equipment, use the buddy system), then remove the exposed person
to fresh air. Keep at rest in a position comfortable for breathing. Get medical advice/attention.IN CASE OF SKIN CONTACT: Immediately drench affected area with water for at least 15 minutes. Remove contaminated clothing immediately. Obtain medical attention if irritation develops or persists. IN CASE OF EYE CONTACT: Immediately rinse with water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Obtain medical attention if irritation develops or persists IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Obtain medical attention.

CONTAINS (CAS#): TRANS-1,2-DICHLOROETHYLENE (156-60-5), Ethanol (64-17-5), Acetone (67-64-1)

INSTRUCTIONS:

  1. Wear protective gloves, protective clothing, eye protection, and face protection.
  2. Before and during application, ensure that the unit is turned off, and remove the filtration media. Cover any necessary parts of the system, such as fan motors and sensors, with a tarpaulin or plastic sheeting if needed. Note: It is best to dispose of and replace air filters when cleaning and treating the air handling system to avoid contamination of the cleaned components downstream of the filters.
  3. Using a coil cleaner (we recommend Vapco’s Quad Power), remove any visible debris before application.
  4. Start appli- cation from the top of the coil, spraying directly onto the coil where needeed. Apply two spray passes to each side of the coil running parallel with fins. Allow each pass to dry before the next one. Do not over-apply on any pass.
  5. To achieve effective surface coverage, maintain a uniform distance from the coil (six to eight inches) during application. Apply the treat- ment to both sides of the coils, including the end plates and tube bends/ends wherever possible.
  6. The cured product’s final appearance may vary from translucent light blue to a darker color, depending on the type, state, and condition of the aluminum fins.
  7. After application, clean any overspray or equipment immediately.
  8. To ensure optimal performance of the coating, wait until the surface is dry before turning on the system. The cure time will depend on environmental factors, typically taking 4-6 hours.
  9. For optimal performance, wait until the product is dry before turning on the system.

PRECAUTIONARY STATEMENT(S):

  • Keep away from heat/sparks/ open flames/hot surfaces.
  • No smoking.
  • Do not breathe dust/mist/ vapors/spray.
  • Wash hands and other exposed areas thoroughly after handling.
  • Wear protective gloves/protective clothing/eye protection/ face protection.
  1. IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
  2. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
  3. IF INHALED: Remove person to fresh air and keep comfortable for breathing.
  4. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.

Immediately call a POISON CENTER/doctor if exposed or concerned. Wash contaminated clothing before reuse. Store locked up. Protect from sunlight. Store in a well-ventilated place. Dispose of contents/container to the specifications of local, regional, national, and international regulations.

CONTAINS (CAS#): lsopropanol (67-63-0), Butoxyethanol (111-76-2), DIMETHYLETHANOLAMINE (108-01-0), Nitrogen (7727-37-9)

Safety Precautions:

  1. Wear high-density rubber gloves, full or half-face masks with filters rated for pesticides and solvents, safety goggles, and a full-body waterproof suit with a hood. Type 1 heavy-duty safety boots are also necessary.
  2. Ensure that the unit is turned off before and during application.
  3. Remove filtration media, and cover them with a tarpaulin or plastic sheeting if needed. Air filters are best disposed of and replaced. Other parts of the system may need to be covered as well, such as the fan motor and sensors.
  4. Remove any visible debris and corrosion before application. Use Vapco’s Quad Power coil cleaner for best results.

Application:

  1. Ensure that Coat It Blue is homogeneous by shaking it vigorously before application.
  2. Decant into Airless spray gun/applicator.
    An electric airless spray gun such as a Wagner W180P, Flexio 585, an industrial unit with a variable pressure airless system or equivalent. (For spraying of micro-channel coils an Atomex HSP-10 is a better option as penetration is increased).
  3. Start applying from the top, spraying parallel to the coils
  4. Spray directly onto the coil and covering the entire surface, paying special attention to end plates and tube ends/elbows.
  5. Apply two spray passes for each side of the coil.
    Allow each pass to partially dry before subsequent passes. Do not over-apply on any pass.
  6. Maintain a uniform distance from the coil (four to six inches) to achieve effective surface coverage. Apply treatment to both sides of the coils wherever possible.
  7. Ensure that the product is applied to coil end plates and tube bends/ends.
    The final appearance of the cured product can vary from translucent light blue to a darker color, depending on the type, state, and condition of the aluminum fins.

Cleanup:

  • Clean any over spray, equipment, etc. immediately after application with Vapco’s Coat It Clean Up.

For optimal performance, it’s important that condensing water does not wet the coated surface.

Precautionary statements:

  • Keep away from heat/sparks/open flames/hot surfaces.
  • No smoking.
  • Keep container tightly closed.
  • Ground/bond container and receiving equipment.
  • Take precautionary measures against static discharge.
  • Do not breathe dust/fume/gas/mist/vapors/spray.
  • Wash hands and other exposed areas thoroughly after handling.
  • Wear protective gloves/protective clothing/eye protection/face protection.

IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.

  • Immediately call a POISON CENTER/doctor if exposed or concerned. Wash contaminated clothing before reuse.
  • In case of fire: Use sand to extinguish.
  • Store in a well-ventilated place. Keep cool. Store locked up.

Dispose of contents/container to the specifications of local, regional, national, and international regulations.

CONTAINS (CAS#): lsopropanol (67-63-0), Butoxyethanol (111-76-2), DIMETHYLETHANOLAMINE (108-01-0)

DIRECTIONS: While wearing proper personal protecive equipment simply spray product on rag then wipe off overspray area. Product can also be poured into Coat It spray equpment to clean equpment out.

PRECAUTIONARY STATEMENT(S):

  • Keep away from heat sparks/ open flames/hot surfaces.
  • No smoking.
  • Keep container tightly closed. Ground/bond container and receiving equipment.
  • Use explosion-proof electrical/ventilating/lighting equipment.
  • Use only non-sparking tools.
  • Take precautionary measures against static discharge.
  • Avoid breathing dust/fume/gas/mist/vapors/spray.
  • Wash hands and other exposed areas thoroughly after handling.
  • Do not eat, drink or smoke when using this product.
  • Use only outdoors or
    in a well-ventilated area.
  • Wear protective gloves/eye protection/
    face protection.
  1. IF SWALLOWED: Call a POISON CENTER/doctor
    if you feel unwell.
  2. IF ON SKIN: Wash with plenty of water and mild soap. Take off immediately all contaminated clothing. Rinse skin with water/shower.
  3. IF INHALED: Remove person to fresh air and keep comfortable for breathing.
  4. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
  5. Call a POISON CENTER/doctor if you feel unwell.

If skin irritation occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention.Take off contaminated clothing and wash it before reuse. In case of fire: Use carbon dioxide to extinguish. Store in a well-ventilated place. Keep cool. Dispose of contents/container to the specifications of local, regional, national, and international regulations.

ADDITIONAL PRECAUTIONS FOR SAFE HANDLING: Do not handle until all safety precautions have been read and understood. Avoid contact with skin, eyes and clothing. Do not breathe gas, mist, spray, vapors. Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and when leaving work. Do not spray on open flame or other ignition source.

CONDITIONS FOR SAFE STORAGE, INCLUDING ANY INCOMPATIBILITIES: Technical Measures: Comply with applicable regulations. Proper grounding procedures to avoid static electricity should be followed. Storage Conditions: Store in a dry, cool place. Keep only in the original container in a cool, well-ventilated place away from ignition sources. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122° F. Keep/ Store away from direct sunlight, extremely high or low temperatures and incompatible materials. Store locked up/in a secure area. Incompatible Materials: Strong acids, strong bases, strong oxidizers. Chlorine. Finely divided metals. Magnesium. Alkaline earth metals.

FIRST AID MEASURES: General Advice:Never give anything by mouth to an unconscious person. If you
feel unwell, seek medical advice (show the label where possible).IF INHALED: First, take proper precautions to ensure your own safety before attempting rescue (e.g. wear appropriate respiratory protective equipment, use the buddy system), then remove the exposed person
to fresh air. Keep at rest in a position comfortable for breathing. Get medical advice/attention.IN CASE OF SKIN CONTACT: Immediately drench affected area with water for at least 15 minutes. Remove contaminated clothing immediately. Obtain medical attention if irritation develops or persists. IN CASE OF EYE CONTACT: Immediately rinse with water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Obtain medical attention if irritation develops or persists IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Obtain medical attention.

CONTAINS (CAS#): TRANS-1,2-DICHLOROETHYLENE (156-60-5), Ethanol (64-17-5), Acetone (67-64-1)

Safety Precautions:

  1. Wear high-density rubber gloves, full or half-face masks with filters rated for pesticides and solvents, safety goggles, and a full-body waterproof suit with a hood. Type 1 heavy-duty safety boots are also necessary.
  2. Ensure that the unit is turned off before and during application.
  3. Remove filtration media, and cover them with a tarpaulin or plastic sheeting if needed. Air filters are best disposed of and replaced. Other parts of the system may need to be covered as well, such as the fan motor and sensors.
  4. Remove any visible debris and corrosion before application. Use Vapco’s Quad Power coil cleaner for best results.

Application:

  1. Connect Gun and Hose to Cylinder
  2. Start applying from the top, spraying parallel to the coils
  3. Spray directly onto the coil and covering the entire surface, paying special attention to end plates and tube ends/elbows.
  4. Apply two spray passes for each side of the coil.
    Allow each pass to partially dry before subsequent passes. Do not over-apply on any pass.
  5. Maintain a uniform distance from the coil (four to six inches) to achieve effective surface coverage. Apply treatment to both sides of the coils wherever possible.
  6. Ensure that the product is applied to coil end plates and tube bends/ends.
  7. The final appearance of the cured product can vary from translucent light blue to a darker color, depending on the type, state, and condition of the aluminum fins.

Cleanup:

  • Clean any over spray, equipment, etc. immediately after application with Vapco’s Coat It Clean Up.

For optimal performance, it’s important that condensing water does not wet the coated surface.

Translate »